Fluke i2000 Flex AC Current Clamp
Fluke i2000 Flex AC Current Clamp is rated out of 5 by 2.
Key features
- Three ranges: 20A, 200 A & 2000 A, 100 mV/A, 10 mV/A & 1 mV/A output
- Ideal for current measurement on thick and hard to reach conductors without breaking the circuit
- Maximum conductor diameter 178 mm
- CAT III 600 V safety rating
Product overview: Fluke i2000 Flex AC Current Clamp
The i2000 is an AC current probe utilizing the Rogowski principle. It can be used to measure currents up to 2000 A when used in conjunction with multimeters, recorders or data loggers. The flexible and lightweight measuring head allows quick and easy installation in hard to reach areas.
Specifications: Fluke i2000 Flex AC Current Clamp
| Electrical specifications | |
| Current ranges | 20 A 200 A 2000 A AC rms |
| Output sensitivity (AC-coupled) | 1 mV 10 mV 100 mV 1 mV per A |
| Load impedance | 100 kΩ minimum |
| Accuracy | at +25°C ±1% of range (45 Hz to 65 Hz) |
| Linearity | 10% to 100% of range ±0.2% of reading |
| Noise | 8 mV AC rms (30 A) 2 mV AC rms (300 A, 3000 A) |
| Frequency range | 10 Hz to 20 kHz (-3 dB) |
| Phase error | < ±1° (45 Hz to 65 Hz) ±10° (at 20 kHz) |
| Position sensitivity (with cable > 25 mm from the coupling) |
Position sensitivity: From 1% up to 3% of range with cable, depending on distance from the center (see figure left). Measurements closer than 25 mm from the coupling are typically greater than 3% of range. |
| External field | with cable > 200 mm from the head ±1% of range |
| Power supply | 2 x AA/MN 1500/LR6 Alkaline, 200 hours, low battery indicator |
| Temperature Coefficient | ±0.08% of reading per °C |
| Working voltage | see Safety standards section 600 V AC rms or DC |
| General Specifications | |
| Head Circumference | 610 mm (24 in) |
| Head cable diameter | 14.3 mm (0.56 in) |
| Head bend radius | 38.1 mm (1.5 in) |
| Cable length (head to electronics) | 2 m (6.56 ft) |
| Output connection | Molded 4 mm safety plugs (not integrated) |
| Operating temperature range | 0°C to +70°C (32°F to 158°F) (head and electronics) |
| Storage temperature range | -40°C to +105°C (-40°F to 221°F) (head) -20°C to +85°C (-4°F to 185°F) (electronics) |
| Operating humidity | 15% to 85% (non-condensing) |
| Weight | 180 g (6.34 oz) (head) 190 g (6.70 oz) (electronics) |
| Safety standards | EN 61010-031: 2002 EN 61010-2-032: 2002 EN 61010-1: 2001 600 Vrms, Category III, Pollution Degree 2 Use of the probe on uninsulated conductors is limited to 600 V ac rms or dc and frequencies below 1 kHz. |
| EMC standards | EN 61326: 1998 +A1, A2, and A3 |
| Dimensions (H x W x D) | 116 x 68.5 x 30 mm (4.56 x 2.69 x 1.18 in) |
Models: Fluke i2000 Flex AC Current Clamp
Fluke i2000 Flex
Can this measure DC current above 1000 A
Rated 4 out of 5 by Fieldservice1 from Accurate This flex CT does work well and I have had mine for many years when they first came out. The ability to wrap around several different conductors makes this a required product for the field. The problem with this product is that the inner flex is a spring that if it is stretched it is permanently damaged and must be replaced. The second problem with this product is that it cannot be calibrated so you need to check for accuracy on a regular basis to make sure you are good to go. These are the only two items where I have seen the weakness and I do recommend the product however one must take care of the equipment.
Date published: 2013-07-25
Rated 5 out of 5 by Hennie from Excellent product with Fluke 233 and wireless screen The i2000 flex probe make it possible to measure amps in a panel with very little space to work. Most clamp on meters needs space for the meter itself and in most cases you cannot reach the cores, especially if more than one core is installed.
The i2000 is flexible, needs very little space and very easy to fit around cores.
Date published: 2013-06-12